When Should You Repair or Replace Your Dehumidifier?

High humidity is one of the major threats against your house’s structural integrity. Most homeowners, today have invested in dehumidification systems to get rid of the excess moisture in the air. Alorair dehumidifiers are used for both commercial and residential spaces. These spaces may differ in need thus, the dehumidification system needs and requirements are different.

While larger spaces require higher capacity Dehumidifiers, the more the Dehumidifiers are required to be operational the higher the chance of the dehumidifier malfunctioning. Malfunctioning of a dehumidifier may lead to increased humidity in the room making it the perfect environment for the growth of mold, mildew, fungi, and dust mite.

For commercial/business premises, a defective Dehumidifier will create a warm uncomfortable workplace. This will not only low the productivity levels of your employees but, will also lead to unhappy customers, who will give your business a bad review. This will lead to your business losing its customers and even worse the bad reviews will put off any potential new customers.

Dehumidifier Diagnostics.

Once you identified that the dehumidification system you have installed is not effectively maintaining the relative humidity levels at the desired levels, you need to follow the following procedure to simply decide whether to repair or completely replace the dehumidifier.

1. Check to see if the dehumidifier is operational.

At this initial step you need to determine where your dehumidifier is either:

Operational and ineffective– the dehumidifier turns on and sounds to be operational but the relative humidity levels remain while the unit fails to extract any water.

This is a common problem experienced by many dehumidifier owners. This problem is usually easily fixed by simply cleaning the dehumidifier.

Here are some of the steps to follow while cleaning the dehumidifier:

  • Unscrew the dehumidifier cover. Follow the unit manual guide.
  • Clean the unit compressor. Ensure you remove all the frost on the compressor.
  • Clean the condenser coils. Remove all the dirt, because the dirt causes the extracted moisture to freeze on the coils hence decrease the dehumidifier's effectiveness.
  • Clear any dirt or dust on the fan blades. Lubricate the fan motor. Once done cleaning fan ensures the fan motor is working effectively if not, replace the motor.
  • Check the humidistat functionality – a defective humidistat could be the reason your dehumidifier has not extracted any humidity from the air.
  • Screw back the cover on to the unit.

If the dehumidifier’s performance does not improve consult your local service center for professional help, before buying a new dehumidifier.

Completely un-operationally/won’t turn on– if you dehumidifier fails to turn on completely, here are the step to follow :

  • Unplug the unit and Check whether the dehumidifier power outlet is fully functional.
  • If the power outlet is fine, firmly plug the dehumidifier back to power and turn on the switch.
  • If the dehumidifier still does not turn on, unplug the unit from power and check for any damage on the power cord. If any damage is spotted, please replace the power cord.
  • If the dehumidifier still does not turn on, remove the unit cover, and check for ice on the dehumidifier parts. Let the ice melt before trying to turn the dehumidifier back on.
  • If the dehumidifier still the dehumidifier does not turn on, remove and check the humidistat.
  • If the dehumidifier still the dehumidifier does not turn on, remove and test the overflow cut off. Most dehumidifiers are built to have an overflow cut off to avoid the water spilling when the collecting tray is full. If the overflow cut off is defective the dehumidifier won’t turn on.
  • Check burn spots on the main circuit board.

If all the above steps fail to restore the dehumidifier functionality, please call a repair person before buying a new dehumidifier.

2. What are the humidity changes that have occurred in the space?  

An increase in humidity can be the cause of the ineffectiveness of your dehumidifier. For instance, if you add an indoor pool to your house, there will be a sharp increase in humidity levels in the house. This increased humidity levels might require you to invest in a higher capacity dehumidifier.

3. How long has the dehumidifier been in service?

Typically most dehumidifiers have the following service life:

  • Residential dehumidifiers – most home dehumidifiers are built to last between 10 to 12 years. They are built with relatively low capacity because the unit is required to service less humid and small spaces. These dehumidifiers consume less power while operational.
  • Industrial or commercial dehumidifiers – commercial dehumidifiers are largely inbuilt, they consume more power and have high capacity thus are able to maintain the humidity levels below 50% in large spaces. Commercial dehumidifiers are built to have a service life of between 7 to 10 years.

 The service life is of any dehumidifier will be affected by:

  • The dehumidifier has to be correctly installed and placed. - – the dehumidifier should be placed at least 6 inches away from any wall, for easy air intake. The air exhaust should also remain clear, for the dehumidifier to remain effective.
  • Airflow problems – the entire airflow and all dehumidification system including ducts and additional air vents, should be maintained to allow adequate airflow within the space. For a dehumidifier to be effective there needs to enough air circulation in the room to ensure all the air in the room is processed by the unit.
  • Power connections – the dehumidifier should be connected to a reliable power outlet to avoid straining the switchboard. This protects your dehumidifier from erratic power problems.
  • The dehumidifier capacity should be slightly above the required capacity. – One of the main reasons why most dehumidifiers break down fast is overworking. If the rooms humidity levels are higher than the capabilities of the dehumidifier capacity. In this situation the dehumidifier will remain operational 24/7, this will make the unit overheat and some parts will wear out fast. Your best option in this situation is to invest in a new high capacity dehumidifier.
  • Operational conditions – if the dehumidifier is installed in the pool room, where the pool water contains chemicals like chlorine, the dehumidifiers service life is greatly reduced. This is because chemicals like chlorine react with metallic parts in the dehumidifier causing them to rust faster, hence the part break or wear out much faster.

It is therefore important to ensure the dehumidifier capacity is powerful enough to completely lower the humidity levels.

4. Failing a dehumidification system.

Signs that a dehumidifier requires to be replaced?

  • The one clear sign of dehumidifier that requires to be replaced is if the dehumidifier requires professional service more than twice a year.
  • If the dehumidifier has had multiple part replacement, especially the compressor.
  • If after all the repair the dehumidifier’s performance remains below par. You don’t need a unit consuming power for no good use.

If your dehumidifier has any of the above re-occurring issues, you will have to invest in a new dehumidifier. It may seem like an expensive option but in the long term, it will be the best and cheapest option.

What should you look out for in your new dehumidifier?

We at AlORAIR are dedicated to helping all our customers easily pick out a dehumidifier that will cater to all their needs. Here are some of the features that set ALORAIR dehumidifiers apart:

  • Auto humidistat – this feature allows your dehumidifier to automatically turn on and off depending on the humidity levels of the air. This will save you money because the dehumidifier will consume less power.
  • Reusable air filters – all our dehumidifiers have a reusable air filter that can be easily cleaned and re-used.
  • Auto defrost – this feature is very helpful to people in colder places because the auto defrosts feature turns off the unit when there is ice on the coils. This allows the ice on the coils to melt and the coils warm up and are able to extract moisture at low temperatures.
  • Auto-restart – the dehumidifier is able automatically to restart in case of a power interruption. The dehumidifier will also be able to maintain the user pre-set requirements.
  • Low noise production – our dehumidifiers produce little or no noise when operational.
  • Continuous drainage system - our high capacity dehumidifiers are built with a continuous drainage system that allows collected water to be emptied out of the unit via a hose and poured out to a safe place.
  • Energy star rated dehumidifier - all ALORAIR dehumidifiers are built to consume less power while extracting more moisture compared to conventional dehumidifiers.

At ALORAIR we offer both portable and permanent installation dehumidifiers! Contact us today for your perfect dehumidifier!


Share this post


Signs That You Need an Air Scrubber

7 Signs That You Need an Air Scrubber for Mold Remediation

When dealing with mold remediation, it is essential to consider all factors that could contribute to the spread of mold spores and the potential health risks associated with exposure. One tool that can greatly aid in the process is an Air Scrubber for Mold Remediation. In this blog post, we will discuss the signs that indicate the need for an air scrubber during mold remediation, Air scrubber vs Negative Air machine and why it is a crucial component in ensuring a successful and thorough removal of mold from your indoor environment. Persistent Musty Odors Signal Hidden Mold A recurrent, musty scent in your space often acts as a red flag, hinting at the potential growth of mold hidden from plain view. This subtle, yet distinct, smell might originate from areas less frequented or visible, such as behind walls, above ceiling panels, or beneath flooring. Such odors suggest that, even in the absence of visible mold patches, mold spores are likely dispersing through the air, which can pose significant health concerns over time. Introducing an air scrubber for mold remediation in these instances plays a pivotal role in capturing these elusive spores, thereby enhancing the quality of indoor air and halting the mold's ability to further permeate your environment. This device operates by drawing in polluted air, filtering out mold spores and other contaminants, and then recirculating cleaner air back into the room. It is a proactive measure in not only addressing the immediate issue of mold spores but also in preventing their future spread. Engaging an air scrubber early in the detection of musty odors can substantially mitigate the risk of mold-related health problems and contribute to maintaining a healthier indoor atmosphere. Its utilization is especially critical in spaces where the source of moisture feeding the mold growth cannot be immediately resolved, offering a means to control the spread and impact of mold spores in the interim. Health Symptoms Related to Mold Exposure Individuals residing or working in environments where mold spores are prevalent may begin to notice an array of adverse health effects. These symptoms often mimic those of allergies and can range from mild to severe, depending on the duration of exposure and the individual's overall health. Common symptoms include persistent coughing, sneezing fits, irritation of the eyes resulting in redness or watering, and dermatological issues such as rashes or hives. For those with pre-existing respiratory conditions, such as asthma, exposure to mold spores can lead to a significant exacerbation of their symptoms, presenting a more pronounced difficulty in breathing or increased frequency in asthma attacks. In cases where individuals are experiencing these health concerns, the presence of mold spores in the indoor environment should be considered a likely contributing factor. An air scrubber becomes an invaluable tool in this context, offering a means to substantially reduce the airborne concentration of mold spores. By filtering out these irritants from the environment, the air scrubber assists in alleviating the health symptoms caused by mold exposure. It serves not only to improve the immediate air quality, thereby providing relief from the symptoms mentioned, but also acts as a preventative measure against the worsening of conditions related to prolonged exposure to mold. Especially in settings where individuals are continually exposed to mold-laden environments—such as homes with ongoing humidity problems or buildings that have suffered water damage—it is imperative to consider the use of an air scrubber as part of a comprehensive approach to mold remediation. This strategy not only addresses the visible mold growth and sources of moisture but also the airborne spores that can continue to affect health even after surface mold has been removed. Through its application, the risk of respiratory and dermatological symptoms related to mold exposure can be significantly mitigated, promoting a healthier living or working space for everyone involved. Visible Mold Growth After Cleaning Discovering mold re-emergence after meticulous cleaning efforts is a telltale sign that airborne mold spores are still rampant, circulating within your space, and settling on surfaces, leading to recurrent mold growth. This persistent issue indicates that cleaning visible mold alone is insufficient to tackle the broader problem of mold spore proliferation throughout the indoor environment. An air scrubber plays a pivotal role in addressing this challenge. By integrating an air scrubber into your mold remediation strategy, you equip yourself with a powerful tool designed to trap these pervasive airborne particles. This device works efficiently to purify the air, ensuring that mold spores are captured before they have the chance to settle and flourish anew. Such a measure is critical in breaking the cycle of mold removal and regrowth. While surface cleaning removes mold from visible areas, it doesn’t address the spores suspended in the air, which are the root cause of continuous mold issues. An air scrubber extends the efficacy of your mold remediation efforts by ensuring that the air itself is treated, removing spores that evade traditional cleaning methods. Deploying an air scrubber after cleaning visible mold effectively targets the invisible threats, offering a layer of protection that prevents the re-establishment of mold colonies. It is an essential step for those who find themselves in a seemingly endless battle with mold reappearances, providing a comprehensive solution that addresses the entirety of the problem. Engaging an air scrubber after initial cleaning not only assists in maintaining a mold-free environment but also supports a healthier indoor air quality, safeguarding against the potential health issues associated with mold spore inhalation. High Humidity Levels and Poor Ventilation Rooms that are frequently exposed to high humidity levels and lack proper ventilation create an environment where mold thrives. Moist, stagnant air is essentially an invitation for mold spores to settle, grow, and multiply. In such conditions, traditional mold remediation techniques may fall short if the air remains untreated. The introduction of an air scrubber during the mold remediation process can be a game changer in these environments. An air scrubber's ability to control the air quality becomes a vital asset in damp, poorly ventilated areas. It works by pulling in the moisture-laden air, filtering out not just mold spores but also other particulates, and then releasing cleaner, drier air back into the space. This process significantly reduces the humidity levels that mold spores require to thrive, thus tackling one of the root causes of mold growth. Moreover, in areas with poor ventilation, pollutants and biological contaminants, including mold spores, can accumulate to levels that pose health risks to occupants. Without adequate air movement to carry these contaminants away, they can contribute to a range of health problems. By capturing these airborne spores, an air scrubber directly addresses the issue of stagnation, promoting a continuous movement of air and ensuring that the environment remains less hospitable to mold. It is also worth noting that reducing the moisture in the air and improving ventilation are not just crucial for mold remediation but are preventative measures as well. Keeping an air scrubber running can help maintain optimal humidity levels and air quality, thereby preventing the conditions mold requires to start growing in the first place. In this way, air scrubbers offer a dual benefit during mold remediation in damp, poorly ventilated spaces: they aid in the removal of existing mold and play a significant role in preventing future growth. After Water Damage or Flooding In the aftermath of water damage or flooding, swift action is crucial to mitigate the potential for mold proliferation, which thrives in the moist conditions left behind. The process of drying out the space, while essential, does not guarantee the elimination of mold spores that may have been dispersed into the air during the event. These microscopic spores can linger, invisible to the naked eye, posing a silent threat to both the structural integrity of the building and the health of its inhabitants. The employment of an air scrubber becomes an indispensable strategy in this scenario. Its function to systematically cleanse the air of these spores helps in curtailing their ability to settle and colonize new areas, effectively halting the cycle of mold growth before it can begin anew. Moreover, the use of an air scrubber in such situations supports the efforts to restore the air quality to safe levels, addressing not only mold spores but other contaminants that may have been introduced by the flooding or water damage. This includes pollutants that are often overlooked, such as bacteria and chemicals from waterborne pathogens or substances dissolved in floodwaters. By incorporating an air scrubber into the remediation efforts post-flooding, you are taking a comprehensive approach to ensure that the environment is not only visually restored but is also truly safe for occupancy. The heightened efficiency of mold remediation efforts, when augmented by air scrubbing technology, underscores the device’s value in maintaining a mold-resilient indoor space following incidents of water damage or flooding. When Preparing for Mold Remediation Embarking on mold remediation is not a task to be taken lightly, as the disruption of mold-infested areas can lead to the unintended dispersion of mold spores throughout your property. To prevent this from occurring, integrating an air scrubber into your remediation strategy is a proactive step that should not be overlooked. Air scrubbers provide a barrier of protection, trapping airborne mold spores that are released during the cleaning and removal process. This is particularly important in enclosed spaces or in situations where mold infestation is severe and the potential for spore spread is high. Utilizing an air scrubber from the outset allows for a controlled environment, ensuring that spores do not find new areas to colonize within the property. It is a critical addition to the mold remediation toolkit for both professionals and homeowners undertaking mold removal efforts. These devices operate by continuously purifying the air, capturing spores, and other particulates, thereby significantly reducing the volume of mold in the atmosphere. Incorporating air scrubbing technology early in the remediation process not only safeguards the health of those involved in the cleanup but also enhances the overall effectiveness of the mold removal efforts. It serves as a foundational step in establishing a clean, mold-free environment, setting the stage for successful remediation work. By prioritizing the containment and filtration of mold spores with an air scrubber, you are taking a comprehensive approach to mold remediation, addressing both visible infestations and airborne contaminants simultaneously. This methodology underscores the importance of not just removing mold, but also ensuring it does not continue to affect the indoor air quality or compromise the health and safety of the building's occupants. Continuous Air Quality Concerns For individuals who face persistent worries about the cleanliness of their indoor air, leveraging an air scrubber as a part of ongoing mold remediation efforts represents a proactive step toward safeguarding health and comfort. Beyond the immediate focus on mold spores, air scrubbers extend their utility by capturing a wide array of airborne pollutants, including dust, pollen, and various allergens that contribute to indoor air quality issues. Their functionality in continually purifying the air translates into a substantial improvement in the living environment, offering a layer of protection that is beneficial even in the absence of visible mold. The dynamic capability of air scrubbers to remove contaminants plays a significant role in addressing underlying air quality concerns that may not be solely related to mold. Regular use of these devices ensures a consistently clean air space, reducing the potential for irritants that can cause discomfort or exacerbate health conditions over time. It’s a strategy that emphasizes not just reactive measures to mold presence but a holistic approach to maintaining an optimal indoor atmosphere. This approach is particularly valuable in environments where the risk of mold growth is heightened due to factors such as high humidity or inadequate ventilation. By integrating air scrubbers into the routine maintenance of these spaces, it's possible to significantly diminish the likelihood of mold development, thereby preemptively addressing one of the root causes of poor air quality. In doing so, the focus shifts from merely combating visible mold to creating a consistently healthier and more comfortable environment, marking a comprehensive commitment to indoor air quality management.  

dehumidifier not collecting water

Dehumidifier Not Collecting Water: Reasons & Solution

Have you ever asked yourself, "why is my dehumidifier not collecting water?" If so, you are not alone. Dehumidifiers are essential appliances in maintaining a comfortable and healthy indoor environment by reducing excess moisture in the air. However, when a dehumidifier fails to collect water, it can be frustrating and concerning. In this blog post, we will explore the various reasons why your dehumidifier may not be collecting water and provide solutions to help you troubleshoot and resolve the issue. Incorrect Humidity Settings - A Simple Oversight Incorrectly set humidity levels can often explain why a dehumidifier seems ineffective in collecting water. This seemingly minor oversight can have a significant impact on the unit's performance. The dehumidifier is designed to kick into action when indoor humidity surpasses its set point. Therefore, if the device's humidity setting is higher than the actual room humidity, it won't activate to reduce moisture, as it perceives no need for action. To troubleshoot this issue, review the current settings on your dehumidifier. Adjusting the humidity control to a lower level might be all that's needed to jumpstart moisture collection. This setting should ideally reflect the specific moisture needs of your space, taking into account both comfort and the prevention of mold growth. The ideal indoor humidity level for most homes ranges between 30% and 50%. Adjustments within this range can help your dehumidifier resume normal operation, effectively managing indoor air quality and comfort. Remember, proper calibration of your dehumidifier's humidity settings not only promotes efficient operation but also contributes to a healthier living environment by maintaining optimal moisture levels. Room Temperature Too Low for Operation A critical aspect often overlooked when troubleshooting a dehumidifier running but no water is due to the impact of room temperature. Dehumidifiers are engineered to perform optimally within a specific temperature range, typically above 65 degrees Fahrenheit. When the environment falls below this threshold, the efficiency of the dehumidifier can be severely compromised. The reason lies in the way dehumidifiers function; they rely on warmer air circulating through the unit to ensure the refrigerant within the coils can effectively condense moisture from the air. In cooler conditions, the coils inside the dehumidifier may start to freeze. This not only halts the moisture extraction process but can also lead to long-term damage to the unit if it continues to operate under these circumstances. To address this issue, there are a couple of strategies you can employ. First, consider the possibility of increasing the temperature of the space, if feasible. This can be achieved by using a portable heater or adjusting your home's heating system to maintain a warmer environment that falls within the dehumidifier's operational range. Alternatively, if adjusting the room temperature is not an option, you might want to move the dehumidifier to a different location where the ambient temperature is within the optimal range for its operation. This could mean relocating the unit to a central area of the home that's naturally warmer or to a specific room where heating is more consistent. It's also beneficial to explore dehumidifiers designed to work in lower temperatures, often referred to as low-temperature dehumidifiers. These models are specially designed to operate efficiently in cooler environments, preventing the coils from freezing and ensuring continuous moisture extraction. Transitioning to a unit suited to your specific environmental conditions can provide a long-term solution to this issue, enabling your dehumidifier to function effectively, irrespective of cooler room temperatures. Clogged Air Filter - Restricting Airflow One of the more common, yet often overlooked which people asked that why my dehumidifier working but not collecting water is due to a clogged air filter. Air filters play a crucial role in the operation of dehumidifiers by filtering out dust, allergens, and other airborne particles before they enter the unit. However, over time, these filters can become clogged with debris, severely restricting airflow. When airflow is impeded, the dehumidifier's ability to draw in moist air and extract water is compromised, leading to decreased efficiency or complete failure to collect water. To address this issue, it is important to regularly inspect the air filter of your dehumidifier. If you discover that the filter is dirty or clogged, it will need to be cleaned or possibly replaced. Most dehumidifier filters can be easily removed and cleaned with mild soap and water. Allow the filter to dry completely before reinstalling it into the unit. Some filters may be disposable and require replacement instead of cleaning. Consult your dehumidifier's user manual to determine the specific maintenance recommendations for your model. Performing this simple maintenance step can significantly impact the performance of your dehumidifier. A clean air filter ensures unobstructed airflow, allowing the dehumidifier to function as intended and efficiently remove moisture from the air. It's a good practice to check the air filter monthly, especially during periods of heavy use, to prevent buildup that can lead to airflow restriction. By keeping the air filter clean, you not only restore the dehumidifier's ability to collect water effectively but also help to improve the overall air quality in your space. The Dehumidifier's Capacity vs. Room Size When evaluating home dehumidifier not collecting water, the correlation between the device's capacity and the room size it's operating in is crucial. Often, homeowners underestimate the importance of matching a dehumidifier's moisture removal capability with the volume of space it needs to service. This mismatch can lead to inefficiency and the apparent failure of the device to collect water. A dehumidifier's capacity is measured in pints of moisture removed from the air over a 24-hour period. This specification is not just a number but a guideline for optimal performance in a given area. A unit too small for a large room will work incessantly yet fail to adequately reduce humidity levels. On the flip side, a dehumidifier with a capacity too large for a space may cycle off too quickly, not allowing for sustained operation necessary to maintain a consistent level of humidity reduction. To determine the right capacity for your needs, consider the size of the area you wish to dehumidify and the level of moisture present. Spaces with high humidity levels, such as basements and bathrooms, often require dehumidifiers with higher capacity. Manufacturers typically provide recommendations for square footage coverage, but it's also wise to account for room conditions. Very damp or wet spaces may need a dehumidifier rated for a larger area than the room's actual square footage. If you find your current portable dehumidifier not collecting water as expected, assess whether the capacity matches the room size and moisture load. It might be necessary to select a larger unit or deploy multiple dehumidifiers across a large or particularly damp area. Addressing the capacity-room size equation not only enhances moisture removal efficiency but also optimizes energy use, contributing to a more comfortable and healthier indoor environment without unnecessary power consumption. Refrigerant Issues - Leaks or Lack of Refrigerant One of the critical components for a dehumidifier's functionality is the refrigerant, which plays a pivotal role in the moisture condensation process. Without the correct amount of refrigerant, or if there are leaks within the system, the dehumidifier's efficiency in water collection can be significantly impaired. A common indicator of refrigerant issues is the dehumidifier running without a reduction in room humidity or without collecting any water. Refrigerant leaks can be subtle and may not be immediately noticeable. These leaks not only prevent the dehumidifier from operating efficiently but can also lead to more significant mechanical failures over time. The refrigerant within a dehumidifier is contained in a closed-loop system; therefore, under normal conditions, it does not deplete. If your dehumidifier is older or has been subjected to rough handling, the likelihood of leaks or refrigerant problems increases. Addressing a refrigerant issue is not a do-it-yourself project due to the complexities involved in handling refrigerants, which require specialized knowledge and tools for safe and effective repairs. Additionally, environmental regulations govern the handling of refrigerants, making it essential to enlist the services of a certified HVAC professional. An expert technician can conduct a thorough examination to detect leaks, assess refrigerant levels, and perform the necessary repairs or recharge the system. In some scenarios, the technician may discover that the issue extends beyond simple refrigerant leaks. The dehumidifier could have a compromised refrigerant line or faults in the compressor that affect the refrigeration cycle. These discoveries underscore the importance of professional intervention when dealing with refrigerant-related problems in dehumidifiers. Engaging a professional ensures not only the restoration of your dehumidifier's functionality but also adherence to safety and environmental standards. Faulty Compressor or Other Mechanical Failures At times, the culprit behind a dehumidifier's inability to collect water may lie within its compressor or stem from other mechanical malfunctions. These issues are more complex and typically require a level of expertise beyond that of a standard homeowner’s troubleshooting skills. The compressor, being the heart of the dehumidifier’s cooling system, plays a crucial role in the condensation process that removes humidity from the air. When it malfunctions, the entire dehumidification process is jeopardized, rendering the appliance ineffective. Mechanical failures can vary widely, ranging from issues with the fan that circulates air through the unit, to problems with the electrical components that power the device. For instance, a fan that’s no longer working at full capacity can significantly reduce the dehumidifier's ability to pull in moist air, while electrical faults may prevent the unit from powering on altogether. Due to the specialized nature of these components and the potential for further damage or safety hazards, attempting to repair a faulty compressor or address mechanical failures without the proper knowledge and tools is not advisable. Instead, professional diagnosis and repair ensure that the dehumidifier is safely and effectively restored to its full operational capacity. Preventive Maintenance to Avoid Future Issues To ensure the ongoing efficiency and longevity of your dehumidifier, adopting a routine preventive maintenance schedule is crucial. A comprehensive approach to maintenance encompasses several key practices beyond the regular cleaning of the air filter mentioned previously. It's equally important to routinely check and clean the dehumidifier's coils, which can accumulate dust and grime, impairing the unit's ability to condense moisture effectively. Just like the air filter, clean coils facilitate optimal airflow and efficiency in moisture removal. Additionally, inspecting and cleaning the water collection bucket is vital to prevent mold and mildew buildup, which could not only affect the unit's performance but also degrade indoor air quality. Ensuring the bucket is free from debris and residue will also help in maintaining a hygienic operation. Proper drainage plays a significant role in a dehumidifier's effectiveness. Regularly verify that any hoses or pipes used for continuous drainage are not kinked, clogged, or obstructed in any way. This will help to avoid water backing up, which could lead to leaks or halt the dehumidifier's operation. Lastly, it’s beneficial to reassess your humidity settings periodically, especially with changes in seasons or in your living environment, to ensure they remain optimal for your current needs. This proactive approach not only aids in preventing operational issues but also contributes to maintaining a consistent and comfortable indoor humidity level.  

dehumidifier buying guide

Dehumidifier Ultimate Buying Guide: When You need & How to Choose

When it comes to maintaining a healthy and comfortable home environment, a dehumidifier can be a valuable tool. Excess moisture in the air can lead to a variety of issues, from mold growth to allergies and respiratory problems.   Understanding Humidity and Its Effects on Your Home   The balance of moisture in your home's atmosphere significantly influences not just comfort levels but also the health of the living environment. Humidity, or the amount of water vapor present in the air, when too high, can lead to several undesirable outcomes. Elevated humidity can cause wallpapers to peel, wood to warp, and a general feeling of dampness that makes the air feel heavier and less comfortable to breathe.  On a more serious note, high humidity provides the perfect conditions for the proliferation of harmful organisms such as mold and mildew, which thrive in moist environments. These organisms can damage your home's structure and negatively impact indoor air quality, potentially leading to health issues for occupants, particularly those with respiratory conditions or sensitivities to allergens. Conversely, air that is too dry can also have adverse effects, including increased static electricity, respiratory discomfort, and the cracking or shrinking of wooden fixtures and furnishings. Understanding the pivotal role humidity plays in your home environment underscores the importance of managing moisture levels effectively for both comfort and health.   The Health and Home Benefits of Using a Dehumidifier   Incorporating a dehumidifier into your living space can significantly enhance both the healthiness and comfort of your environment. By effectively managing humidity levels, these devices help mitigate a host of health issues, including reducing the incidence of asthma attacks and alleviating symptoms related to allergies by creating an environment that is less hospitable to dust mites, mold, and other allergens. Beyond health, the structural integrity of your home benefits greatly from the use of a dehumidifier. Excess moisture is a leading cause of damage to home furnishings, causing wood to swell and warp and promoting the growth of mold on walls and ceilings. By maintaining optimal humidity levels, dehumidifiers protect wallpapers, paintings, and electronic devices from the damaging effects of excess moisture, thereby preserving the aesthetic and structural elements of your home. Moreover, by fostering a drier atmosphere, these devices can enhance the overall comfort of living spaces, making them feel cooler and more pleasant. In essence, the deployment of a dehumidifier serves as a proactive measure towards ensuring a healthier and more enjoyable indoor environment for occupants.   Identifying When You Need a Dehumidifier   Recognizing the need for a dehumidifier in your home can be pivotal in maintaining a healthy and comfortable living environment. Several telltale signs indicate the presence of excessive humidity, necessitating the intervention of a dehumidifier. Persistent musty odors emanating from rooms or basements are a clear indicator of high moisture levels that can foster mold and mildew growth. The appearance of mold spots on walls or ceilings is not just an aesthetic issue but a health risk that requires immediate action. Frequent condensation on windows, especially during colder months, suggests that indoor air contains too much moisture. Additionally, if you or family members start experiencing exacerbated allergy symptoms indoors, it could be due to allergens like dust mites thriving in the humid conditions. Peeling wallpaper or paint and warping woodwork are also signs that the humidity levels in your home might be too high. Paying attention to these indicators can help you determine the right time to invest in a dehumidifier, thus preventing further damage to your home and improving the indoor air quality for its occupants.   Types of Dehumidifiers Explained   In the world of dehumidifiers, the two dominant models are refrigerant and desiccant. Refrigerant dehumidifiers, also known as compressor dehumidifiers, operate by drawing warm air over cold coils. This process causes moisture in the air to condense into water, which is then collected in a tank or drained away. They are particularly effective in warmer climates and are widely used due to their efficiency in reducing high humidity levels. On the other hand, desiccant dehumidifiers employ a moisture-absorbing material to extract water from the air. As air passes through the dehumidifier, it encounters a desiccant material that binds and removes moisture. This type of dehumidifier is especially useful in cooler environments, as it does not rely on a temperature differential to extract moisture. Additionally, desiccant models can operate effectively at lower temperatures, making them ideal for spaces like basements in cooler climates. Understanding these distinctions is crucial for making an informed choice. The selection between a refrigerant and a desiccant dehumidifier should be guided by the specific conditions of your environment, including temperature and humidity levels, to ensure optimal performance and moisture control.   Key Features to Consider When Choosing a Dehumidifier   Selecting the right dehumidifier involves more than just picking any model off the shelf; it requires a careful consideration of several important factors to ensure it meets your needs effectively. Capacity is paramount, as it determines how much moisture the dehumidifier can remove from the air over a 24-hour period. This is typically measured in pints and should align with the humidity level and size of the area you wish to dehumidify. Equally critical is the unit's operating temperature range, which must be suitable for the climate of your home to ensure efficiency throughout the year. The water tank size or the availability of a continuous drainage option plays a significant role in the dehumidifier's convenience and maintenance requirements. Larger tanks need less frequent emptying, but a direct drain feature can eliminate this chore entirely. Energy efficiency is another crucial aspect; models with an Energy Star rating consume less power, leading to lower electricity bills and a smaller environmental footprint. Additionally, features such as auto-defrost, which prevents the coils from freezing in cooler temperatures, and humidistat controls, which allow you to set the desired humidity level for your space, can greatly enhance usability and effectiveness. Taking these key features into account will guide you towards choosing a dehumidifier that best suits your space, ensuring optimal moisture control and a healthier indoor environment.   How to Choose the Right Size Dehumidifier for Your Space   Determining the correct dehumidifier size involves understanding both the area of the room and the level of dampness present. For standard rooms with moderate humidity, a basic guideline is to use a dehumidifier capable of removing approximately 10 pints of water per day for every 500 square feet. However, for spaces that are very wet or have persistent moisture issues, such as basements that smell musty or have visible mold, the capacity should be increased. In these instances, a model designed to extract 12-14 pints per 500 square feet is more appropriate. It's also essential to account for the ceiling height; for rooms with ceilings higher than eight feet, adjust the capacity upward to compensate for the extra volume of air. Remember, choosing a dehumidifier with a slightly higher capacity than needed can be more efficient in terms of energy usage and may better handle unexpected increases in humidity levels. Utilize these guidelines as a starting point to select a model that will effectively control moisture and contribute to a healthier indoor environment in your specific area.   Maintenance Tips for Your Dehumidifier   Ensuring your dehumidifier runs efficiently for years involves routine upkeep. Start by emptying and cleaning the water tank at least once a week to prevent mold and mildew buildup, using mild soap and water. The air filter, which traps dust and particles, should be checked monthly. If it's dirty, clean it according to the manufacturer's instructions, typically with a vacuum or warm soapy water. Don't forget about the coils; they should be dusted off with a soft brush or cloth to maintain optimal performance, especially before the start of heavy usage seasons. For those models with user-replaceable parts, inspect them periodically for wear and tear, and replace as needed. It's also wise to ensure the unit is positioned in a way that allows for proper airflow; avoid placing it against walls or furniture. Following these maintenance steps will help maximize the efficiency of your dehumidifier, contributing to a healthier and more comfortable home environment.   The Best Places in Your Home for a Dehumidifier   Identifying the optimal spots for positioning a dehumidifier can significantly enhance its effectiveness in controlling moisture levels throughout your home. High-humidity areas naturally serve as prime locations. Basements often bear the brunt of excess moisture due to their below-ground positioning, making them prime candidates for dehumidification. Similarly, crawl spaces, which can trap moisture and foster mold growth, benefit greatly from consistent humidity control. Bathrooms are also hotspots for humidity, especially after showers and baths, which can leave lingering moisture in the air. A dehumidifier in this space can prevent mold and mildew buildup, protecting walls and fixtures. Laundry rooms, where dryers may not vent completely to the outside, can also accumulate moisture, making them another key location for dehumidification efforts. In addition to these areas, consider rooms where valuable items or sensitive materials are stored. Libraries, where books can suffer from damp conditions, and rooms containing musical instruments or electronics, which can be damaged by excessive moisture, are also ideal places for a dehumidifier. Remember, while targeting these high-priority areas, it's crucial to ensure the unit is not obstructed by furniture or curtains to maintain optimal airflow. Strategically placing dehumidifiers in these areas can protect your home's structure and create a healthier living environment for everyone inside.   Budgeting for Your Dehumidifier: Cost vs. Quality   Navigating the balance between cost and quality when purchasing a dehumidifier is crucial. Initial expenditures can be deceiving, as more expensive units often bring advanced features that lead to better energy efficiency and longevity. For example, a model with an Energy Star rating, although priced higher, will use less electricity, thereby reducing utility bills over time. This is a critical consideration, especially for those planning to use the dehumidifier frequently or in larger spaces where the energy consumption can quickly accumulate. Additionally, durability is a key factor influenced by the quality of construction and materials used in the dehumidifier. High-quality models are less likely to require frequent repairs or replacements, offering greater value over their lifespan. It's also worth considering the warranty and after-sales support offered by the manufacturer, which can provide peace of mind and further justify a higher upfront investment. On the other hand, opting for a cheaper model to save on initial costs can sometimes lead to increased expenses in the long run. Such units may have higher operating costs, less efficiency, and a shorter lifespan, necessitating earlier replacement. Therefore, when budgeting for a dehumidifier, it's important to evaluate not just the purchase price but the overall cost of ownership, including energy consumption, maintenance requirements, and the potential need for future replacements.   Top Mistakes to Avoid When Buying a Dehumidifier   One critical misstep to avoid is underestimating the importance of accurately sizing the dehumidifier for your space. A unit too small will struggle to effectively reduce humidity levels, while an oversized one can lead to unnecessary energy consumption. Equally, failing to choose the appropriate type based on your climate—whether it’s a refrigerant or a desiccant model—can drastically affect performance. Overlooking the unit's energy efficiency can also be a costly mistake. Models without an Energy Star rating might seem cheaper initially but can lead to higher electricity bills over time. Additionally, ignoring features that enhance convenience and functionality, such as a built-in hygrometer, continuous drainage options, or auto-shutoff capabilities, can diminish the user experience and effectiveness of the device. Lastly, inadequate maintenance, by not regularly cleaning or emptying the unit, can lead to poor air quality and reduce the lifespan of the dehumidifier. Avoiding these common errors will help ensure you select a dehumidifier that meets your needs, operates efficiently, and provides lasting comfort and protection for your home.


← Older Post Newer Post →